Did you know that the F35 error code is a common issue faced by many owners of Whirlpool washers? This pesky error can disrupt your laundry routine and leave you scratching your head in confusion. But fear not! We’re here to help you troubleshoot and fix the F35 code on your Whirlpool washer, so you can get back to washing with ease.
Whether you have a Whirlpool Duet washer or another model, the F35 error code typically indicates a problem with the pressure sensor switch. This crucial component is responsible for detecting the water level in the washer and preventing overfilling. When the pressure sensor switch malfunctions, it triggers the F35 error code, halting the wash cycle and leaving you with a machine that refuses to cooperate. But don’t worry, we’ve got the solutions to fix it!
Key Takeaways:
- The F35 error code is a common issue faced by Whirlpool washer owners.
- The error is typically caused by a malfunctioning pressure sensor switch.
- Checking the hose and wire connections to the pressure sensor switch is the first step in troubleshooting the F35 code.
- If needed, replacing the pressure sensor switch can resolve the error.
- Cleaning the soap dispenser drawer can be an alternative solution if the F35 code persists.
Steps to Replace the Pressure Sensor Switch
If you’ve determined that the pressure sensor switch is the cause of the F35 error code on your Whirlpool washer, you’ll need to replace it. Follow these steps to successfully replace the pressure sensor switch:
- First, unplug the washer to ensure your safety.
- Locate the pressure sensor switch, which is usually located near the top of the washer.
- Disconnect the wire harness from the sensor by gently pulling it out.
- Next, remove the mounting screw that secures the sensor in place.
- Once the screw is removed, carefully pull the pressure sensor switch out of its housing.
- Take note of the position of the wires connected to the old sensor.
- Now, it’s time to install the new pressure sensor switch. Align the new switch with the housing and push it into place.
- Secure the new sensor by tightening the mounting screw.
- Reconnect the wire harness to the new sensor, ensuring a secure connection.
- Double-check all connections and make sure everything is properly secured.
- Finally, plug the washer back in and test it to see if the F35 error code has been resolved.
Following these steps should help you successfully replace the pressure sensor switch on your Whirlpool washer and resolve the F35 code issue. If you’re unsure about any step or encounter difficulties, it’s always best to consult a professional technician or refer to the manufacturer’s manual for further guidance.
Alternative Solution for Fixing F35 Code
If replacing the pressure sensor switch does not resolve the F35 error on your Whirlpool washer, there is an alternative solution you can try. This method involves cleaning the soap dispenser drawer, as a clog or buildup in this area can sometimes trigger the F35 error.
To clean the soap dispenser drawer, carefully disassemble it and remove any soap residue or mold that may be blocking the flow of water. This simple cleaning may fix the issue and eliminate the F35 error code.
Step-by-Step Guide to Cleaning the Soap Dispenser Drawer:
- Unplug your Whirlpool washer from the power source.
- Open the detergent drawer and remove it from the washer.
- Inspect the drawer for any visible clogs, soap residue, or mold. If necessary, use a soft brush or cloth to remove any buildup.
- Fill a sink or bucket with warm water and a mild detergent.
- Submerge the soap dispenser drawer in the soapy water and let it soak for a few minutes.
- After soaking, use a brush or cloth to scrub away any remaining residue.
- Rinse the drawer thoroughly with clean water to remove all traces of soap.
- Allow the drawer to dry completely before reassembling it back into the washer.
- Plug your washer back in and test for the F35 error code.
This alternative solution can often be effective in resolving the F35 error on your Whirlpool front load washer. By cleaning the soap dispenser drawer, you can eliminate any potential clogs or blockages that may be causing the error code.
| Common Issues with F35 Code on Whirlpool Washer | Possible Solutions |
|---|---|
| The pressure sensor switch is malfunctioning. | Replace the pressure sensor switch. |
| Clogs or buildup in the soap dispenser drawer. | Clean the soap dispenser drawer. |
| Issues with wire connections to the pressure sensor switch. | Check and reconnect wire connections. |
| Faulty main control board. | Replace the main control board. |
Conclusion
Dealing with the F35 error code on your Whirlpool washer can be frustrating, but with the right troubleshooting steps, you can resolve the issue. Start by checking the hose and wire connections to the pressure sensor switch, and if needed, replace the switch. If the problem persists, try cleaning the soap dispenser drawer.
By following these steps, you can successfully fix the F35 code on your Whirlpool washer and get back to doing your laundry with peace of mind. Remember to always unplug the washer before performing any repairs or maintenance to ensure your safety.
We hope that this guide has been helpful in addressing the f35 error code on your Whirlpool washer. If you have any further questions or need additional assistance, don’t hesitate to reach out to Whirlpool customer support. Happy washing!
FAQ
What does the F35 error code mean on a Whirlpool washer?
The F35 error code on a Whirlpool washer usually indicates a failure in the pressure sensor switch.
How can I troubleshoot the F35 error on my Whirlpool washer?
To troubleshoot the F35 error, you can check the hose connecting to the pressure sensor switch for any kinks, clogs, or damage. Verify that it is properly connected on both ends. Remove the hose from the sensor and blow through it to ensure there are no restrictions. Additionally, check the wire connections to the sensor at both the sensor and main control board.
How do I replace the pressure sensor switch on my Whirlpool washer?
To replace the pressure sensor switch on your Whirlpool washer, follow these steps:
1. Unplug the washer and turn off the water supply.
2. Remove the top panel of the washer.
3. Locate the pressure sensor switch, usually located near the top of the washer.
4. Disconnect the wire connections from the sensor.
5. Remove the mounting screws securing the sensor in place.
6. Install the new pressure sensor switch by reversing the above steps.
What should I do if replacing the pressure sensor switch does not fix the F35 error?
If replacing the pressure sensor switch does not resolve the F35 error, you can try cleaning the soap dispenser drawer. Soap residue or mold buildup in this area can sometimes trigger the F35 error. Carefully disassemble the soap dispenser drawer and remove any debris or blockages.
How common are issues with the F35 code on Whirlpool washers?
The F35 code is relatively common on Whirlpool washers, particularly on front load models. However, proper troubleshooting and maintenance can usually resolve the issue.
Leave a Reply